Dragonburner¶
References¶
Backplate¶
Pick one backplate and toolhead PCB option below.
- Dragonburner spacer is required - goes between backplate and toolhead
- Backplate assembly instructions
- Requires supports. Printing instructions
| Backplate | PCB Mount Options | Notes |
|---|---|---|
| [official] Draftshift Design Dragonburner Backplate |
Voron PCB Mounts with extended extruder mount | Needs extended extruder mount to raise extruder so stock PCB mount will clear the OptoTap board |
| [userMod] TheSin's Dragonburner backplate |
TheSin's PCB36 mount Extruders: Orbiter 2.5, HGX Sherpa, G2SA |
Adds attachment points for PCB mount. May not be compatible with all extruders |
| [userMod] Traxman25's Dragonburner backplate |
Dragonburner Orbiter EBB36 mount Extruders: Orbiter 2 |
Combined with PCB mount for EBB36-compatible boards |
Backplate BOM for All Tools¶
- [4] m3 heat inserts
- [3] Ø4x12mm ssRod (dowel pin) with a rounded end (if it has female threads on the back it will be listed as an M3, but make sure the pin is 4mm OD, that is what is important. We recommend the threaded pins for better fixing)
- [1] 6x3mm magnet (N52 Highly recommended to counter the pull from the umbilicals. Note that most magnets not from a reputable source may say N52 but aren't actually. Recommend one of the two links below.)
- [2] m3x6 or m3x8 FHCS (Flat head countersunk screw, MUST BE MAGNETIC. no stainless, as per TAP)
- [1] OptoTap (only the sensor PCB is required)
- [1] m3x8 BHCS (optional in v1.1)
BOM Additions for Dragonburner¶
- [1] m3x12 BHCS (optional to keep spacer in place)
- [2] m3x35 SHCS
- [2] m3 heat inserts
- [2] m3x8 BHCS (optional in v1.1)
- Several 5x2 or 5x3 N52 magnets to hold toolhead to dock (Highly recommended for non-magnetic docks)
Toolhead Options & Mods¶
- Dragonburner numbered cowls (non-magnetic)
- Dragonburner cowl mods
- Eddy Coil Mount in a DragonBurner Tool-head
Umbilical¶
- NH36 Sock for board using theSin's PCB36 mount. But zip-ties work also.
Dock¶
| Dock Width | Stubby Dock Compatible |
|---|---|
| 60mm | ✅ Yes |
Maximum Toolheads per Printer Size¶
| Printer Size | Max Toolheads |
|---|---|
| Voron 250 | 5 |
| Voron 300 | 5 |
| Voron 350 | 6 |
Calculation assumes 5mm spacing between docks. See Docks for details.
Official Dock Types (Draftshift Design)¶
| Dock Type | Description | Link |
|---|---|---|
| Standard Dock | Full-height dock with back and base | Dragonburner Back and Base |
| Stubby Dock | Shorter dock (no vertical supports, crossbar attachment only) - saves ~10mm Y build space | Dragonburner Stubby Base |
User Mods¶
| Dock Type | Size | Description | Link |
|---|---|---|---|
| Magnetic Dock | 60mm | Magnetic dock (no uprights needed) | Dragonburner magnetic dock |
| Angry Docks | 60mm | Angry-style docks for magnetic Dragonburner | Angry docks for magnetic Dragonburner (discord link) |
| Screw Docks | 60mm | Screw-based docks for hooking toolheads | Screw docks |
Additional Resources: * Common components for your dock type * Modular dock assembly guide
Tips & Suggestions¶
-
NOTE: If you plan on using the Tapchanger Dragonburner dock you must use the custom cowl by OstroMa.
-
We always recommend to use the original cowls when possible and the Modular Dock does not require any special Cowl, print the original from the Dragonburner repo.